Television box converter
Create the converter field at the earliest opportunity to check on DTV sign reception and troubleshoot any problems. (1) The converter field needs to be connected to the antenna and television; (2) in the event that round RF coaxial cable is being used, the television should be set-to Channel 3; and (3) the converter field must be activated utilizing the “channel scan” or “auto scan” function. The converter field wont operate properly before channel scan is carried out. VCRs and DVD people is linked utilizing a variation of this standard set-up, as explained further below. The converter package must be switched on to be used and stations must be altered utilizing the converter field. As soon as a converter box is established, the tv must be able to get more than 20 digital tv networks.
Fundamental Converter container Set-Up: stick to the converter box’s imprinted instructions for connecting the converter package. Change the television’s energy “off” and disconnect the antenna. Link the antenna into the “Antenna In” port in the converter field utilizing the antenna’s present RF coaxial cable (or include a 300/75 ohm transformer in the event that antenna has actually a flat wire; see Twin-Lead Wiring Diagram). Plug the brand new RF coaxial cable supplied with the converter box to the “Out to TV” slot from the converter field and into the “Antenna In” or RF coaxial connector interface in the television; see Coaxial Wiring Diagram.
Red, White, and Yellow Composite A/V Cables: In the event that television has actually three readily available purple, white, and yellow harbors (jacks), the three-part composite A/V cable can be used – as opposed to the circular RF coaxial cable – to present much better image and noise. Composite A/V harbors could also be used if an RF coaxial connector interface just isn't available on the tv (typically because another unit is utilizing the RF interface).
Switch on the container and TV: After linking the antenna into converter field while the package towards the tv, switch on both the converter package additionally the tv. Separate remote settings when it comes to converter box while the tv could be essential, many converter package remotes may be able to get a grip on tv amount and on/off functions. If a round RF coaxial cable will be made use of, set the tv to Channel 3 and then leave it set indeed there. If there is a little selector slide-switch in the back of the converter box, it must be set-to "3" (for station 3), not to 4. regarding the television, select “antenna” (maybe not “cable, ” etc.) as input origin. On some larger screen tvs, it may be necessary to select “Video 1” or “Video 2” while the supply, alternatively; this might be accessed utilising the “Menu” or “Set-Up” option on the television’s radio control. The target is to obtain a screen with lettering and numbers, which is the preliminary sign through the converter box.
Perform a Channel Scan: Through the converter package selection (hit the “Menu” key on handheld remote control), find and highlight the “Channel Scan” or “Auto Scan” or “Auto Program Channels” function with the converter package's handheld remote control. After that push the “OK” or “Select” button. The scanning procedure will likely then start and may also just take two or three mins to accomplish. As soon as that is done, the tv screen should get significantly more than 20 electronic channels. If only some stations can be obtained, duplicate the channel scan function. It there are many than just a couple of “No Signal” signs, look at the antenna and adjust it as needed. See the area above, entitled Antenna and Reception Issues.
Channel Numbering: Most channels are transferring several indicators. These are labeled with a station number followed closely by a dash or period, then 1, 2, 3, or 4, with regards to the amount of additional sub-channels. For example, channel 26 has four digital PBS sub-channel indicators: 26-1, 26-2, 26-3, and 26-4.
I don't have cable or satellite, we hooked outdoor antenna up and have had great reception but not now, WHY!!? | Yahoo Answers
ever since television stations went digital we have had our televisions hooked up to an outdoor antenna and have gotten great reception until about two weeks ago now we have no signal, why has this happened and can we do anything to correct it???
Check the cable. You may have had a hungry rat or squirrel chewing on your wires. If that doesn't reveal any problem, plug the antenna input into a different TV and see if that works. If so, it's your TV. If not, it's the antenna or cable. If the first two fixes don't work, try running a second cable from the antenna to the TV to completely bypass the original cable. Finally, verify that the antenna is positioned properly and didn't get blown off line or something.